Code Alarm CA680 Manual do Utilizador

1MM1 Installation InstructionsAvoid mounting components or routing wires nearhot surfacesAvoid mounting components or routing wires nearmoving partsTa

2. 16 PIN MAIN HARNESS CONTINUEDChassis Ground Source (-) (BLACK)Connect the BLACK wire to a solid chassis ground point using a ring terminal and se

11Negative Unlock Output (GREEN)Negative Lock Output (BLUE)Negative Second Door Unlock Output (TAN)The door lock / unlock outputs are designed to con

123. DOOR LOCKSNegative Unlock Output (GREEN)Negative Lock Output (BLUE)Negative Second Door Unlock Output (TAN)Positive Switching and Positive Swit

13Negative Unlock Output (GREEN)Negative Lock Output (BLUE)Negative Second Door Unlock Output (TAN)Reverse Polarity (5-Wire Doorlocks) and Reverse P

14Negative Unlock Output (GREEN)Negative Lock Output (BLUE)Negative Second Door Unlock Output (TAN)One Wire Negative Multiplexed and One Wire Negative

15Negative Unlock Output (GREEN)Negative Lock Output (BLUE)Negative Second Door Unlock Output (TAN)One Wire Positive Multiplexed and One Wire Multipl

163. DOOR LOCKSNegative Unlock Output (GREEN)Negative Lock Output (BLUE)Negative Second Door Unlock Output (BLUE/GREEN)Adding Aftermarket ActuatorsAf

172 Pin Override Push-Button Switch: (Blue Connector)The BLACK and GRAY twin lead wires loaded in the two pin blue connector are the ground supply an

186. System Testing1. Follow each instruction below.2. Verify that the system operates as indicated under each instruction. Refer to the system owner

19Press DISARM:1. Doors unlock.2. Factory alarm (if equipped) is turned off.3. Siren/horn sounds once/ parking lights flash once.4. Courtesy lights tu

2MM1 System LayoutGREEN UNLOCK (-)BLUE LOCK (-)TAN TRUNK (-)BROWN MANUAL DISARM INPUTORANGE GROUND WHEN ARMEDPURPLE DOOR TRIGGER (+)GREEN/

20MM1 ITS FunctionalityMM1 ITS IntroductionThe MM1 may be used as a MM1 ITS (Interior Theft Sensor) and when doing so it is designed to honk the horn

21MM1 ITS LAYOUTGREEN N/ABLUE N/ATAN FACTORY ALARM TRIGGERBROWN N/AORANGE N/APURPLE DOOR INPUT (+)GREEN/VIOLET DOOR INPUT (-)RED +12

22

3SETUP & PROGRAMMING - CONSUMER MODEConsumer Mode Transmitter Programming Bank 1 (3 Chirps)1. Turn the ignition ON.2. Press and hold the overrid

4MM1 - Consumer Mode Programming GuideFeature Bank 1 - 3 Chirps Transmitter ProgrammingFeature Bank 2 - 4 Chirps 1 LED Flash 2 LED Flashes 3 LED Flash

5Transitioning into Lot Mode1. Turn the ignition ON.2. Press and hold the override button.3. Within 10 seconds the system will chirp (3) three time

6SETUP & PROGRAMMING - LOT MODELot Mode Transmitter Programming Bank 1 (3 Chirps)1. Turn the ignition ON.2. Press and hold the override button.3

7MM1 - Lot Mode Programming GuideFeature Bank 1 - 3 Chirps Transmitter ProgrammingFeature Bank 2 - 4 Chirps 1 LED Flash 2 LED Flashes 3 LED Flashes 4

82. BASIC INSTALLATION - 16 PIN MAIN HARNESSStarter Input (Key Side) (PURPLE/RED) / Starter Output (Motor Side) (PURPLE)Locate the vehicle sta

92. 16 PIN MAIN HARNESS CONTINUEDManual DISARM Input (BROWN)This wire will DISARM the security system when a POS or NEG pulse is applied to it from