Code Alarm CA680 Manual do Utilizador

CA 680 Installation InstructionsAvoid mounting components or routing wires nearhot surfacesAvoid mounting components or routing wires nearmoving part

(+)(-)Positive Polarity Output(+)(-)Negative Polarity Output2. BASIC INSTALLATION - 22 PIN BASE HARNESSStarter Input (Key Side) (GREEN) / Starter

Negative Door Input (GREEN)Locate the vehicle’s dome light or door pin switch wire.Verification: This wire will register ground (NEG) when the door

Hood Pin Input (GRAY)Install a Hood Pin Switch and connect to the GRAY wire. This connection is required for Remote Start.Verification: This wire when

Parking Light Output (+/-) (WHITE)Locate the vehicle’s parking light wire at the vehicle light switch.Verification: This wire will register positive v

SONGBIRD (BROWN/WHITE) Speaker Accessory requiredThis wire controls the Speaker accessory (Not Included)Connect this wire to one of the WHITE/BLACK wi

Parking Brake Input (GRAY/BLACK)NOTE: The following connection is only required for Turbo Timer.Verification: This wire will register ground when the

3. 6 PIN REMOTE START HARNESSBattery Power 1 (12 AWG) (RED)Locate the vehicle battery wire(s) at the ignition switch.Verification: These wires will

Active Output (18 AWG) (BLUE/BLACK)The Active Output/Ignition 3 output wire provides a ground output when the remote start function is activatedand re

Pulse Before Start (20 AWG) (LIGHT GREEN/BLACK) 500mA OutputLocate the factory perimeter alarm disarm wire from the key cylinder inside the drivers d

AUX 1 (PINK/BLACK)This wire provides a 500mA negative output capable of driving relays. For Control of optional accessories(i.e. Power Window/Sunroof,

SAFETYCONTROLSWITCH34Lt BLUE/GREENBLUEUNLOCK SENSE INPUTTRUNK PIN INPUT(-)567891011121314151617181920BLUE/WHITEWHITE/BLUEGRAYGRAY/BLACKGREENBLACKBROWN

Negative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock Output (BLUE/GRE

6. DOOR LOCKSNegative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock Ou

Negative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock Output (BLUE/GRE

6. DOOR LOCKSNegative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock Ou

Negative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock Output (BLUE/GRE

6. DOOR LOCKSNegative Lock Output / Positive Unlock Output (GREEN)Negative Unlock Output / Positive Lock Output (BLUE)Negative Second Door Unlock Ou

2 Pin Transponder Control Output: (Yellow Connector)This output is intended to allow the control of a transponder bypass interface module or transpond

9. System Testing1. Follow each instruction below.2. Verify that the system operates as indicated under each instruction. Refer to the system owners

Press DISARM1. Doors unlock2. Factory alarm (if equipped) is turned off.3. Siren/horn sounds once/ parking lights flash once.4. Courtesy lights turn o

10. Mounting the Module / Finishing the Installation1. Mount the module to a brace or wire harness under the dash. The module and harnesses must be c

22 Pin Base HarnessCA 680 System Layout4-Pin Tracking Port(White)4-Pin Receiver Port(Black)4-Pin Shock Sensor Port(Tan)4-Pin Auxilliary Port(Green])2-

2 Pin Transponder Port (YELLOW)6 Pin Remote Start Harness3 Pin Door Lock Harness (WHITE)1STLOV21+DER21YROSSECCAEGNARO32YROSSECCAETIHW/EGNARO42NOITINGI

Programming OptionsRF ProgrammerThe RF Programmer allows you to customize the system to fit the individual needs of the consumer, usinga handheld devi

Selecting Programmable Features1. Press the POWER button to turn the system ON.2. Once powered up the MENU screen will be displayed.3. Use the UP &

CA680 - Programming GuideFeature Bank 1 - 3 Chirps Transmitter ProgrammingFeature Bank 2 - 4 Chirps RF Programmer Receive BankFeature Bank 3 - 5 Chirp

1. SETUP & PROGRAMMINGTransmitter Programming (3 Chirps)1. Turn the ignition ON.2. Press and hold the valet/override button.3. Within 10 secon

Programming Tach RateThe unit will not operate unless tach is programmed or tachless option is turned ON. If an attempt is made tostart the vehicle