Code Alarm CA-535 Manual do Utilizador Página 28
- Página / 144
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Hardware Set Up
535 User's Manual Chapter 4 21
CHAPTER 4
HARDWARE SET UP
Hardware configuration determines the available outputs as well as the type of
input signal. The 535 controller comes factory set with the following:
• All specified modules and options installed (for details, refer to the Order
Code in Chapter 1).
• Process variable and remote setpoint set to accept a milliamp input.
• Relay outputs set to normally open.
Altering the factory configuration of the 535, requires accessing the circuit
boards, and locating the jumpers and output modules (see Figure 4.1).
1. With the power off, loosen the four front screws, and remove them.
2. Slide chassis out of the case by pulling firmly on the bezel.
A detailed view of the circuit boards appears in Figure 4.2.
After configuring the hardware, or if no changes are necessary, continue set-
ting up the process as needed.
HARDWARE INPUT TYPES
The Process Variable
The 535 accepts several different types of process variable signals. Set a jumper
location to specify the type of input signal. Set the signal range in the software
(see Chapter 5 for software menus, or Chapter 7 for applications).
The jumpers for the process variable are located on the Microcontroller Circuit
Board (see Figure 4.2). The factory default is Milliamp. Locations are marked
as follows:
V Voltage
MA Milliamp
TC
▼▼
▼▼
▼ Thermocouple with downscale burnout
TC
▲ ▲
▲ ▲
▲ Thermocouple with upscale burnout
RTD RTD
NOTE: Thermocouple downscale
and upscale burnout offers a choice
in which direction the controller
would react in the event of
thermocouple failure. For example,
in heat applications, typically, it is
desirable to fail upscale (TC s) so
that the system does not apply more
heat.
NOTE: Hardware configuration of the
controller is available at the factory;
Consult a Moore Industries application
engineer for details.
Figure 4.1
Location of Printed Circuit Boards for
Hardware Configuration
MICROCONTROLLER
BOARD
POWER SUPPLY
BOARD
OPTION BOARD
FRONT FACE
- Table of Contents 2
- List of Figures 5
- CHAPTER 1 8
- INTRODUCTION 8
- Introduction 10
- Operation 12
- CHAPTER 2 12
- BASIC INTERFACE 12
- Install / Wire 18
- CHAPTER 3 18
- INSTALLATION 18
- AC Power Input 20
- Process Variable Input 20
- Transmitter 21
- MILLIAMP INPUT 22
- 2-wire transmitter with 22
- Hardware Set Up 28
- CHAPTER 4 28
- HARDWARE SET UP 28
- Controller Set Up 34
- CHAPTER 5 34
- SOFTWARE CONFIGURATION 34
- PARAMETER VALUE CHARTS 61
- CHAPTER 6 70
- FAST MENU 71
- MENU MENU 71
- MENU DISPLAYFAST 71
- R –50.0% to 50.0% 72
- 21. PROP. BND.:X 74
- 22. RESET:X 74
- 23. RATE:X 74
- 25. TRIP:X 74
- CHAPTER 7 78
- APPLICATIONS 78
- Applications 100
- Menu Flowcharts 112
- APPENDIX 1 112
- MENU FLOWCHARTS 112
- Parts List 114
- APPENDIX 2 114
- PARTS LIST 114
- APPENDIX 3 116
- TROUBLESHOOTING 116
- Troubleshooting 116
- Calibration 118
- APPENDIX 4 118
- CALIBRATION 118
- Specifications 124
- APPENDIX 5 124
- SPECIFICATIONS 124
- Glossary 128
- APPENDIX 6 128
- GLOSSARY 128
- APPENDIX 7 134
- Isolation Block Diagram 135
- RETURN PROCEDURES 136
- 500 SERIES 137
- Installation 138
- EMC Directive 89/336/EEC 142
Manuais e produtos relacionados com Sistemas de ignição com controlo remoto Code Alarm CA-535
(23 páginas)
(8 páginas)Dataram DTM64356A Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Speichermodule Dataram DTM64356A.
Wir stellen 1 PDF-Handbücher Dataram DTM64356A zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Datenblatt
Comentários a estes Manuais