Code Alarm CA-640 Manual de Instruções

1InstallationInstructionsAvoid mounting components orrouting wires near hot surfacesAvoid mounting components orrouting wires near moving partsTape or

102. Advanced Harness (A)2/A Factory Alarm Arm (20 AWG-) (BLACK/GREEN) Connect the 2/A wire to the vehicle anti-theft arm wire (ifequipped).Verificati

1112/A Aux - 3 500ma (20 AWG - ) (GRN/WHT)This wire provides a 500ma negative output capable of drivingrelays. For control of optional accessories (i.

123/C Ignition 2 Output (14 AWG-) (PINK/WHITE)30 Amp Fused Relay Battery Feed (12 AWG) (RED)Note: The 3/C wire is the ground trigger to an external Ig

137/C Brake Input / Glow Plug Input (20 AWG+) (BROWN)Connect the 7/C wire to the vehicle brake light wire.Verification: This wire registers positive

1410/C Active Output (20 AWG -) (BLUE/BLACK)Connect the 10/C wire to add-on relays as described in Diagram14, or to an optional component requiring a

15A. System Power-Up1. All connections must be secure and well insulated.2. Insert fuses inside of the control module in their respective slots.3. Pl

16Note: Transmitters must be programmed prior to these steps.1. Repeat steps 1-4 of Remote Transmitter Programming(previous page).2. Press and release

17D. Adjusting the IT-sTM (Interior Theft Sensor)The IT-sTM is factory pre-set at a moderate sensitivity level and hastwo adjustment points: Lite-Tou

18F. Programming OptionsDefault settings in BOLDOPTION DESCRIPTIONOption Bank 0 - 3 Chirps (Learn Transmitters)Option Bank One - 4 Chirps (Alarm Opti

19OPTION DESCRIPTIONOption Bank Six - 9 Chirps (Installer Options)STATUS INDICATOR1. Door Trigger Polarity (1) Positive (2) Negative ON(1)OFF(2)2

21. Lock Switch (87a) (BLU/BLK) 1. Parking Light Output (WHITE) 1. HVAC2 Input (BLUE)2. Factory Arm/RAP (-) (BLK/GRN) 2. Lock M

20 How to use E-CodeE-Code is a alternate method of emergency overriding and willtake the place of the push-button when selected. The factory preset

216. System Testing1. Follow each instruction below.2. Verify that the CA-640 operates as indicated undereach instruction.3. Check the appropriate wi

226. System Testing, cont’dStart output configuration:Tach Sense ModeIf Tach input wire is connected and Tach Sense Mode is enabled,the starter will

236. System Testing, cont’d3. LED (blue light) flashes slowly for duration of arm cycle.4. After 5 seconds, unit monitors all entrances and sensors.P

246. System Testing, cont’d4. Courtesy lights turn on for 60 seconds, or until LOCK is pressed orignition is turned on.5. Vehicle starter is enabled.

257. Personalized Transmittter’sA. What is Personalized Transmiiters functionThis system has the capability to active an auxilary when the unitrecie

2610. Mounting the Module / Finishing the InstallationIMPORTANT!Perform System Test (page 22-25) before and afterthis section.1. Use the supplied long

27CA-640.p65 10/20/03, 7:48 PM27

31. Basic Harness (B)IMPORTANT!!!• Remove fuses from Module before installation.• Solder and tape all connections.1/B Parking Light Output (16 AWG) (W

4Refer to Diagram 2 to connect to the vehicle’s drivers unlock wire.Type 2: Positive 5-Wire Door Lock SystemPolarity fuse = Positive (+)Single-Stage U

5Type 3: Negative 3-Wire Door Locking SystemPolarity Fuse = NegativeSingle-stage unlockConnect the 2/B wire to the vehicle lock wire.Connect the 14/B

6Ground for negativepolarity system+12v fused forpositive polaritysystem+12v fusedTo vehicle door lock module24/BDiagram 8Type 5: Resistor Door Lock

73/B Courtesy Light Output (16 AWG) (BLACK/WHITE)Locate the vehicle courtesy light wire.Verification: This wire is usually the door pin switch wire. R

81. Basic Harness (B), cont’d.11/B External Start Trigger/ Lite Touch Input (20 AWG +/-)(WHITE/BLUE)This wire will activate the Car Start System or

91. Basic Harness (B), cont’d.+12 Volts21/BTo Horn WireDiagram 10 20/B Positive/Negative Door Input (20 AWG) (GREEN/VIOLET)Connect the 20/B wire to th